• 設計及び問い扱い説明書
  • ユニバーサルジョイントの選定手順
  • ご注文に際してのお願い

PJ(φ13)series

(stainless-steel bolt M4)
Easy-work with using both left and right-tightening in pairs, in case of symmetry.
Cross 90°hole
for right-angle shaft attachment
φ22x42
Cross 45°hole
for use in pairs.
for attachment at an angle.
φ22x42
PJ204 / PJ204M
One-sided boss
for free assembly with other parts
Part No. L
PJ204 23
PJ204M 45
φ22x23+L
Cross one-side through
one-side hole
for free,
no tightening
φ22x37
Cross one-side
stuck
one-side hole
for free,
stuck at the bottom
φ22x37
Cross one-side
free
to be nearly flat
for pipe face
φ22x34
Cross one-side
ree-stuck
to be nearly flat
for pipe face
with head face
φ22x34
Vertical-horizontal hole
for flame support or T-shape attachment.
φ22x35
Cross 90°hole
for tightening on
top and bottom.
φ25x34
Cross 45°hole
for tightening on top and bottom.
for use in pairs.
for attachment at an angle.
φ25x34
Vertical-horizontal hole
one-side hole for free / for flame support
φ22x28
Strut 45°
for use in pairs.
for attachment at an angle.
φ22x42
Both-side free
flexible movement
for cross direction
φ22x26
T-shape
one-side open
for flame support / flexible movement
φ22x26
Cross-end T
for flame support / flexible movement
φ22x37
Round plateT
for flame support or T-shape attachment
φ30x20
PJ220-PJ225
Screw tapped
for parts or board attachment
Part No. L M
PJ220 14 M4
PJ221 14 M5
PJ222 18 M6
PJ223 18 M8
PJ224 23 M10
PJ225 23 M12
PJ230-PJ233
Screw tapped
for parts attachment such as Adjuster
Part No. M
PJ230 M6
PJ231 M8
PJ232 M10
PJ233 M12
φ22x37
Support Rings
for PIJON positioning /
Slip prevention when screw loosening
φ28x8.5
positioning alignment, supported by PJ237
Support Rings
to add PJ238 and adjust positioning
by M4 screw loosening,
in case of slight movement
φ28x8.5
Shelf plate-fixing
slip prevention for shelf plate in parallel with shaft hole
φ22x27
Shelf plate-fixing
slip prevention for shelf plate in parallel with shaft hole
φ22x27
Shelf plate support
for shelf plate support or shaft stopper
φ22x23
Shelf plate-fixing
for fixing
by 2-φ4.5 with shaft
φ26x25
For corner fixing
φ26x15
Shaft-end horizontal
for stage of
horizontal shaft
φ26x28
Shaft-end
for strut base
φ26x19
T-shape
both-side open
for holding
T-shape shaft
φ22x35
Cross-end L
for corner part assembly
φ22x37
3 direction hole
for multistage assembly of rack or flame
φ22x54
Decorating ball
for attachment
on the shaft edge
sphereφ22
Decorating ball
for attachment
on the shaft edge
sphereφ27
Horizontal-split with cross 90°hole disassembly type
for later attachment without flame disassembling
φ28x34
Long-dwell for M6
to raise from flat face or insert to φ13 hole
φ13x28
Short- dwell for M6
to raise from flat face or insert to φ13 hole
φ13x14
PJ262-PJ265
Female screw dwell
to raise from flat face or insert to φ13 hole (screw to be attached)
Part No. M L
PJ262 M4 10
PJ263 M5 10
PJ264 M6 12
PJ265 M8 14
PJ266-PJ269
Female screw dwell
to raise from flat face or insert to φ13 hole (screw to be attached)
Part No. M
PJ266 M4
PJ267 M5
PJ268 M6
PJ269 M8
For hinge
one-side free with
the other side fixed
φ22x46x16
Ball for 6 directions
for main part such
as display
sphereφ39
Horizontal 4 directions
for main part such as display
φ40x18
8°for 3 legs
for pole support
φ39x30
Corner for external tightening
to set the corner of flame assembly
42x42x28
Corner for
internal tightening
to set the corner
of flame assembly
42x42x28
2 shaft poles
enforced vertical shaft
42x42x28
3 shafts fixing
enforced horizontal type
42x42x28
Low-profile 3 shafts fixing
to set the corner
of flame assembly
42x42x14
Low-profile corner
to set the corner
of flame assembly
42x42x21
Different Cores for corner (external tightening)
for easier corner assembly
or disassembly
42x42x28
Different Cores for corner
(internal tightening)
for easier corner assembly or disassembly
42x42x28
Split T
to tuck without disassembling flame (capable of later attachment)
36x29x22
Split T
to tuck without disassembling flame (capable of later attachment)
28x29x22
Split Cross
to tuck without disassembling flame (capable of later attachment)
36x29x22
Split Cross
to tuck without disassembling flame (capable of later attachment)
28x29x22
Split with
5 directions hole
to tuck into the main part of flame without disassembling
(later attachment)
28x29x22
Split 45°for strut
for use in pairs /
for strut support with 45°at an angle
(later attachment)
36x29x22
45°for W strut
for device or main part such as display
(later attachment)
29x60x22
Split with parallel two-shafts hole
for holding 2 shafts (PJ302-PJ304) /
Later attachment OK
29x40x22
Split with parallel two-shafts hole
for holding 2 shafts (PJ303-PJ304) /
Later attachment OK
29x48x22
Split T
to tuck without disassembling flame (capable of later attachment)
33x29x22
Split T
to tuck without disassembling flame (capable of later attachment)
25x29x22
Split L
for L-shape flame support
(later attachment)
28x29x22
Split 45°for strut
for use in pairs /
for strut support with 45°at an angle
34x29x22
Split with parallel
two-shafts
for holding 2 shafts (PJ302-PJ304) /
both-sides open / later attachment OK
29x34x22
Split with parallel
two-shafts
for holding 2 shafts (PJ303-PJ304) /
both-sides open / later attachment OK
29x43x22
Split T for rail
to tuck a guide pipe (capable of later attachment)
31x29x22
Split T for rail
to tuck a guide pipe (capable of later attachment)
23x29x22
Split with
6 directions hole
to tuck into the main part of flame without disassembling
28x29x22
One-side split with cross 90° ◎
to tuck without disassembling flame
(capable of later attachment)
25x62x24
Split with horizontal two-shaft T-shape
for holding 2 shafts (PJ302-PJ304) /
both-sides open / later attachment OK
29x50x22
Shelf plate support
To a shaft hole and parallel with shelf board gap prevention
29x20x11
Shelf plate support
to set right angle with shaft hole / for slip prevention
29x20x11
Shelf plate support
for shelf plate support or shaft stopper
24x20x11
PJ503-PJ505
Screw tapped
for parts or board attachment
Part No. M
PJ503 M3
PJ504 M4
PJ505 M5
20x29x11
Two screw tapped
for parts or board attachment
32x25x12
Shaft hole addition
to add a hole with combination of 2 kinds havingidentical G dimension with 400 type
29x28x11
Shaft hole addition
following PJ506/516
29x28x11
Shelf plate-fixing
or fixing by 2-φ5
with shaft
29x25x11
For corner fixing
15x29x11
Block for slight adjustment
M6 screw for slight adjustment
29x28x11
Free-direction addition
2 parts combination for free shaft direction
29x20x11
Horizontal hole
to raise horizontal and vertical shaft
28x38x10
Vertical hole
to fix vertical shaft
24x38x24
Flange
for lateral side or vertical shaft attachment
40x27x10
Joint
for additional joint of shaft
28x20x27
PJ605-PJ607
Joint
to use female screw. For parts attachment
Part No. M
PJ605 6M
PJ606 M8
PJ607 M10
28x20x27
Vertical-horizontal hole
for L-shape attachment and horizontal hole / stuck at the bottom
28x38x24
Vertical-horizontal T shape
for vertical/lateral shaft attachment
28x38x28
Vertical hole with plate
to fix by screw even on aluminum flame
(guide dowel is prepared)
30x70x34
(:pipe hole )
* For 300, 400 type, please match the mark on both edge phase on assembly.
※You may download 3D CAD drawings by clicking on the part number of interest.