• 設計及び問い扱い説明書
  • ユニバーサルジョイントの選定手順
  • ご注文に際してのお願い

PH(φ25)series

(stainless steel bolt: M5, M6 / ●: M5)
Easy-work with using both left and right-tightening in pairs, in case of symmetry.
PH100 / PH101
Cross 90°hole
for right-angle shaft attachment
φ37x75
PH104 / PH104M / PH104L
One-sided boss
for free assembly with other parts
Part No. L
PH104 40
PH104M 70
PH104L 100
φ37x39+L
PH109
Vertical-horizontal hole
for flame support
or T-shape attachment.
φ37x62
PH114
Strut 45°
for attachment
with inclined angle.
φ37x80
PH119
Strut 90°
for attachment
with inclined angle.
φ37x80
PH120-PH122
●
Screw tapped
for parts or board attachment
Part No. M
PH120 M5
PH121 M6
PH122 M8
48x38x14
PH123-PH125
Screw tapped
for parts or board attachment
Part No. M
PH123 M8
PH124 M10
PH125 M12
φ37x59
PH126 / PH127
●
Two screw tapped
for parts or board attachment
Part No. M
PH126 M5
PH127 M6
48x38x14
PH128 / PH129
●
Two screw tapped
for parts or board attachment
Part No. M
PH128 M5
PH129 M6
59x38x14
PH130 / PH131
●
Shelf plate support
for shelf plate support or shaft stopper
Part No. L
PH130 24
PH131 35
PH154
Horizontal two-shaft hole
for shaft or PH104 attachment
φ37x81
PH237
●
Support Rings
for　PIJON positioning /
Slip prevention when screw loosening
φ46x11
positioning alignment, supported by Ph237
PH238
●
Support Rings
to add PH238 and adjust positioning
by M4 screw loosening,
in case of slight movement
φ46x11
PH246
Shaft-end
for strut base
φ39x25
PH260 / PH261
Long-dwell for M8
to raise from flat face or
insert to φ25 hole
Part No. L
PH260 Long-dwell 40
PH261 Short- dwell 25
PH262 / PH263
Screw hole dwell for M8
to raise from flat face or insert to φ25 hole、
screw to be attached
Part No. L
PH262 28
PH263 13
PH320 / PH321
3 direction hole
to set the corner of flame assembly
57x63x34
◎
PH400
Split T
to tuck without disassembling flame (capable of later attachment)
65x53x36
◎
PH405 / PH406
Split 45°for strut
for use in pairs /
for strut support with 45°at an angle
71x53x36
◎
PH408
Split with parallel
two-shafts hole
for shaft or
PH104 attachment
68x40x36
◎
PH600
●
Horizontal hole
to raise horizontal and vertical shaft
43x64x17
　　PH603　●
Flange
for lateral side or vertical shaft attachment
18x54x38
PH613 / PH614
●
Vertical hole
to fix vertical shaft
φ58x30
(:pipe hole )
* For 300, 400 type, please match the mark on both edge phase on assembly.
※You may download 3D CAD drawings by clicking on the part number of interest.